Home  ›  How to Make a Origami Rocket That Flies

How to Make a Origami Rocket That Flies

Written By Sunday, November 21, 2021 Add Comment Edit

Download Article

Download Article

3...2...1...Blastoff! This paper rocket is based on actual NASA blueprints, and will really fly. With a few simple materials and a little handiwork, you'll be able to blast off into infinity and beyond in no time!

  1. 1

    Draw a circle on your paper. You'll use this to form the rocket's nose cone. A streamlined and pointy nose cone will really increase your paper rocket's aerodynamics.[1]

    • Place your plastic cup on a clean area of the paper, bottom side down.
    • Trace around the bottom to make a perfect circle.
    • Make a small dot in the center of the circle.
    • Draw a small triangle with the tip ending at the circle. It should look like a slice of pie that is about 1/8th the size of the circle.[2]

  2. 2

    Cut out the entire circle. Go slow and steady and try to keep it as a perfectly round circle.

    Advertisement

  3. 3

    Make a cone out of the circle. These next steps will help you turn your circle into a cone.[3]

    • Cut out the triangle piece. Now your circle will look like Pacman.
    • Fold down the right and left flaps to form a cone. It will look kind of like a teepee or a party hat.
    • Hold it on the top and bottom with two hands and twirl it around in your finger to turn it into a pointy cone.
    • Use tape to seal the cone. One piece should be enough to hold the seams in place and keep your cone tight, like a dunce cap or ice cream cone.

  4. 4

    Attach your cone to the body. Now that you have both the rocket body and nose cone, it's time to put them together. [4]

    • Put the cone on one of the rocket ends and tape them together.
    • It's okay if the cone is a little bigger than the body, just make sure you mold it tightly around the cylinder and tightly seal it with tape.
    • You can test the seal by blowing into the open end of the cylinder. If some air leaks out, use more tape to seal it up.

    Advertisement

  1. 1

    Draw a 5x5 inch square. This will be as the body for your rocket. It's best to use regular 8x11 computer printer paper. Start at the left side of your paper and make a dot at the 5-inch mark. Next, measure 5 inches (12.7 cm) from the top of the paper and make a mark there. [5] Draw lines to connect these points and form a square in the top left corner.

    Take your time, there's no rush. You want your rocket body to be sleek and clean, so try to cut true to the lines you drew.[6]

  2. 2

    Make a cylinder out of the square. You'll need a pencil and some Scotch tape for this next part.[7]

    • Place the corner of your square at the tip of the pencil with the rest of the paper pointing towards the eraser.
    • Wrap the paper tightly around the pencil. You want to make this as tightly wrapped as possible. Keep rolling until you use all the paper to make a small, tight cylinder around the pencil.
    • Carefully wiggle the pencil out of the cylinder while holding the paper so that it stays rolled.
    • Gently use the thumb and forefinger of your other hand to push down on the top and bottom of the cylinder to make sure it's even.
    • Tape around the seams in three different places (top, middle, bottom) to make sure the cylinder stays rolled. Now you've got a body for your rocket!

    Advertisement

  1. 1

    Drawing a pair of 2x1 inch triangles. To draw a triangle, all you have to do is draw a 2 inch (5.1 cm) vertical with your ruler, and then a 1-inch horizontal line from its base, and connect the opposite ends with a diagonal line.[8]

  2. 2

    Cut out the triangles. You might want to use a smaller pair of scissors for this part.

  3. 3

    Tape one your triangles to the cylinder body. Putting wings on your rocket will make it more aerodynamic and able to cut through the air better, fly faster, and go further.[9]

    • You want the shortest part of your triangle to be at the base of the cylinder, with the tall vertical part running up the cylinder's body.
    • The diagonal part of the triangle (also called the hypotenuse) should look like a fin extending from the body of your rocket.

  4. 4

    Repeat for the second triangle. Tape your second wing in the same way, directly across from your first wing.

    Advertisement

  1. 1

    Insert the straw. Take your plastic drinking straw and insert it into the open end of your rocket.[10]

  2. 2

    Aim. Be careful not to point your rocket at anybody, and especially not anyone's face. Instead, make a target and aim for that. How to Make a Target

  3. 3

    Blow. Take a deep breath in and exhale quickly and forcefully through the straw.

  4. 4

    Blastoff! Watch as your homemade paper rocket blasts through the air.

    Advertisement

Add New Question

  • Question

    What will happen if I use cardboard instead of paper?

    Community Answer

    It most likely won't work because it will be too heavy and you can't round it using the pencil. So try to use paper.

  • Question

    How long does it last?

    Community Answer

    It will might last about 20 to 40 launches, depending on the impacts and conditions it's in. It isn't supposed to last forever because it is just paper, so it might get ripped or torn after a couple of uses.

  • Question

    Do I have to use a straw to blow the rocket?

    Community Answer

    No, not necessarily. However it is better to use a straw as it is manual, and you can choose precisely with how much power and accuracy you want to shoot it.

  • Question

    How do I join the cone and the cylinder?

    Community Answer

    With glue or glue stick. Do NOT use staples -- they will make your rocket too heavy.

  • Question

    How far will the rocket fly, and is it worth the time?

    Community Answer

    It depends on how hard you blow, but it goes pretty far, at least 5-10 feet. If you want to make an easy rocket, I'd say it's worth it, and it's pretty fun for kids.

  • Question

    If it's bigger, will it go farther?

    Community Answer

    Not necessarily. It depends on how good the creases are and the precision of the folds. It will go farther if air catches under the wings, so size doesn't really matter.

  • Question

    What can you do if the rocket is to tight?

    Community Answer

    Unroll the areas that are too tight and loosen them.

  • Question

    How can I tape the cone and the cylinder together?

    Community Answer

    You can use a glue stick to attach them together. Do not staple, this will add too much weight to the top of your rocket, and it will not reach its maximum potential.

  • Question

    Why did the rocket I made not fly?

    Community Answer

    You may have used too much tape or glue (whatever you used to connect the cylinder and the cone).

  • Question

    Can it fly without a straw?

    Community Answer

    Not necessarily, because you won't be able to fire it. You can try making a straw out of paper.

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

  • Tightly seal all your seams with tape. You don't want any air leaking out. Tight seals will keep all the air inside the rocket and make it fly better.

  • Have your tape pre-cut into strips and waiting for you on the edge of your table. This will make it easier to tape your rocket pieces while having your hands free to cut and roll the paper.

  • Make your cone really pointy. This will increase it's aerodynamics.[11]

  • Experiment by changing the wing size, shape, and number to see how these affect your rocket's flight.[12]

Thanks for submitting a tip for review!

Advertisement

  • Be careful not to aim the rocket towards anyone because the rocket could poke out an eye.

Advertisement

Things You'll Need

  • Regular 8x11 paper. You can use regular white computer printing paper, or color paper if you want a fancier rocket. Do not use cardstock or construction paper -- they are not as easy to roll or bend.
  • Scotch tape.
  • A thin drinking straw.
  • Scissors. If you doing this activity with kids, consider using safety scissors.
  • A ruler.
  • A small plastic drinking cup, like the kind typically used at kid's parties.

About This Article

Article SummaryX

To make a paper rocket, cut out a 5 by 5 inch paper square, a paper circle the size of a plastic cup, and two paper triangles that are 2 inches long and 1 inch wide. Wrap the paper square around a pencil tightly so it forms a cylinder, tape it, and remove it from around the pencil. Cut the circle so it looks like Pacman, tape it into a cone, and tape the cone to the top of the cylinder. Finally, tape the two triangles to the bottom of the cylinder to create wings. You now have a paper rocket! For tips on how to fly your rocket, scroll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 338,436 times.

Did this article help you?

How to Make a Origami Rocket That Flies

Source: https://www.wikihow.com/Make-a-Paper-Rocket

0 Response to "How to Make a Origami Rocket That Flies"

Post a Comment

Subscribe to: Post Comments (Atom)

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel